Why is my camera not sending pictures or not connecting?

Which product do you have?

Previous
Next

Solutions for the CLOM Cam 5 and icucam 5

Here are steps to check:

  1. Is image transmission switched on?
    In the icuapp or under https://enter.icuserver.com/account/cameras you can switch image sending on and off.
    (Sometimes it happens that this function is pressed by mistake when logging on to the camera) 
  2. Is there a memory card with max. 128GB in the camera?
    If necessary, format the memory card with the camera: Camera menu -> Settings -> Format SD card 
  3. Important: Afterwards, make a Resetto correct any inappropriate settings:
    Camera menu-> Settings-> Reset camera 
  4. Switch off the camera. 
  5. Check that the antenna is screwed on securely. 
  6. Slide the switch to SETUP and wait up to 3 minutes without pressing a button. 
  7. Repeat this process if you do not receive a connection.
    The connection is successful if 4G/3G or 2G is positioned above the antenna bar.
  8. If a connection is established ("Connection OK"), wait until the message "Status OK" or "Status message successful" appears.
    Registration of the camera is then complete. 
  9. Take a test photo.
    Press the right arrow button to create a test photo, which is immediately sent to your icuapp and to https://enter.icuserver.com/account/photos is sent.
  10. If the status message (8.) does not appear, please carry out a firmware update.
    You can find the instructions here: icucam 5 - Firmware Update
  11. Then please follow the points again. 4 to 9.

  Solution did not help? Contact us

Solutions for the icucam4

Here are steps to check:

  1. Is image transmission switched on?
    In the icuapp or under https://enter.icuserver.com/account/cameras you can switch image sending on and off.
    (Sometimes it happens that this function is pressed by mistake when logging on to the camera) 
  2. Is there a memory card with max. 32GB in the camera?
    If necessary, format the memory card with the camera: Camera menu -> Settings -> Format SD card 
  3. Important: Afterwards, make a Resetto correct any inappropriate settings:
    Camera menu-> Settings-> Reset camera 
  4. Switch off the camera. 
  5. Check that the antenna is screwed on securely. 
  6. Slide the switch to SETUP and wait up to 3 minutes without pressing a button. 
  7. Repeat this process if you do not receive a connection.
    The connection is successful if 4G/3G or 2G is positioned above the antenna bar.
  8. If a connection is established ("Connection OK"), wait until the message "Status OK" or "Status message successful" appears.
    Registration of the camera is then complete. 
  9. Take a test photo.
    Press the right arrow button to create a test photo, which is immediately sent to your icuapp and to https://enter.icuserver.com/account/photos is sent.
  10. If the status message (8.) does not appear, please carry out a firmware update.
    You can find the instructions here: icucam 4 - Firmware Update
  11. Then please follow the points again. 4 to 9.

  Solution did not help? Contact us

Solutions for the icucam lite

Here are steps to check:

  1. Is image transmission switched on?
    In the icuapp or under https://enter.icuserver.com/account/cameras you can switch image sending on and off.
    (Sometimes it happens that this function is pressed by mistake when logging on to the camera)
  2. Is there a memory card with max. 32GB in the camera?
    If necessary, format the memory card with the camera: Camera menu -> Settings -> Format SD card
  3. Important: Afterwards, make a Reset, to correct any inappropriate settings:
    Camera menu-> Settings-> Reset camera
  4. Switch off the camera.
  5. Check that the antenna is screwed on securely.
  6. Slide the switch to SETUP and wait up to 3 minutes without pressing a button.
  7. Repeat this process if you do not receive a connection.
    The connection is successful if 4G/3G or 2G is positioned above the antenna bar.
  8. If a connection is established ("Connection OK"), wait until the message "Status OK" or "Status message successful" appears. Registration of the camera is then complete.
  9. Take a test photo. Press the right arrow button to create a test photo, which is immediately sent to https://enter.icuserver.com/account/photos is sent.
  10. If the status message (8.) does not appear, please carry out a firmware update.
    You can find the instructions here: icucam lite - Firmware Update
  11. Then please follow points 4 to 9 again.

  Solution did not help? Contact us

Solutions for the icuhunt/icutrap

Here are steps to check:

  1. Activate image dispatch (if not already active)
  2. Switch on the camera
    Wait until it has a signal.
  3. Then in the menu under "Other" Perform a "Reset".
  4. Switch off the camera
  5. Switch back to "Setup"
    Wait until there is a signal (can take a very long time, up to 3 minutes)
    The camera may switch off. By pressing the button regularly
    (e.g. menu every 20 seconds) this can be prevented.
  6. Then press "OK"
  7. Now a picture should be taken and sent: "send smtp". If "Send successful" appears, then everything is OK.
  8. If "no signal" appears, repeat the process two to three times.

  Solution did not help? Contact us

Solutions for the 3G camera simHERO

Here are steps to check:

Please note the information on the Test procedure screen:

  1. Batteries full?
  2. Set the camera switches to the following position:
    "ON" / photo symbol / "25" or "56" / "ON"
  3. Then switch on and briefly (!) press the "OK" button until the screen appears.
  4. When the screen is active, take a photo by pressing the "OK" button once
    -> It then takes one to two seconds for the photo to start being sent.
  5. Please note the screen now. If the photo has been sent correctly ("Send SMTP" message), this will be confirmed on the screen ("Sending successful"). The duration of the sending process depends on the quality of the mobile phone network reception. (normally 30 seconds)

 

Appears Error 500then there is a problem with the mavoco SIM card. In this case, please contact the SIM card operator mavoco/SimHero: www.simHERO.com or via help@simHERO.com.

In the event of other error messages or NO MESSAGES, carry out the reset shown:
You can also find additional information here: Camera reset.pdf

Please note:

  1. The file name (MMS.cfg) must not be changed.
  2. The name must correspond exactly to "MMS.cfg"! e.g. MMS(1).cfg, MMS(2) or similar would be incorrect and the reset would not work.
  3. The file must be saved to the top level of the SD card, i.e. please do not save it in a file folder.

  Solution did not help? Contact us

Solutions for the CLOM EasyCam and icueasy

Here are steps to check:

  1. Is image transmission switched on?
    In the icuapp or under https://enter.icuserver.com/account/cameras you can switch image sending on and off.
    (Sometimes it happens that this function is pressed by mistake when logging on to the camera) 
  2. Is there a memory card with max. 32GB in the camera?
    If necessary, format the memory card with the camera: Camera menu -> Settings -> Format SD card 
  3. Important: Afterwards, make a Resetto correct any inappropriate settings:
    Camera menu-> Settings-> Reset camera 
  4. Switch off the camera. 
  5. Check that the antenna is screwed on securely. 
  6. Slide the switch to SETUP and wait up to 3 minutes without pressing a button. 
  7. Repeat this process if you do not receive a connection.
    The connection is successful if 4G/3G or 2G is positioned above the antenna bar.
  8. If a connection is established ("Connection OK"), wait until the message "Status OK" or "Status message successful" appears.
    Registration of the camera is then complete. 
  9. Take a test photo.
    Press the right arrow button to create a test photo, which is immediately sent to your icuapp and to https://enter.icuserver.com/account/photos is sent.
  10. If the status message (8.) does not appear, please carry out a firmware update.
    You can find the instructions here: icueasy - Firmware Update
  11. Then please follow the points again. 4 to 9.

  Solution did not help? Contact us

Solutions for the CLOM Cam-S

Here are steps to check:

  1. Is your subscription active? Please check your ICU CLOM app to see if your subscription has expired.
  2. Is there a memory card with max. 128GB in the camera?
    If necessary, format the memory card with the camera: Camera menu -> Settings -> Format SD card 
  3. Important: Afterwards, make a Resetto correct any inappropriate settings:
    Camera menu-> Settings-> Reset camera 
  4. Switch off the camera. 
  5. Check that the antenna is screwed on securely. 
  6. Slide the switch to SETUP and wait up to 3 minutes without pressing a button. 
  7. Repeat this process if you do not receive a connection.
    The connection is successful if 4G/3G or 2G is positioned above the antenna bar.
  8. If a connection is established ("Connection OK"), wait until the message "Status OK" or "Status message successful" appears.
    Registration of the camera is then complete. 
  9. Take a test photo.
    Press the right arrow button to create a test photo, which is immediately sent to your icuapp and to https://enter.icuserver.com/account/photos is sent.
  10. If the status message (8.) does not appear, please carry out a firmware update.
    You can find the instructions here: CLOM Cam-S - Firmware update
  11. Then please follow the points again. 4 to 9.

  Solution did not help? Contact us